Product Details

Brief Introduction

 

When ordering this series slip ring type rotor motor, in addition to special requirements, generally its ambient temperature does not exceed 40 ℃, altitude does not exceed 1000m, does not allow the open type motor installed in dangerous, flammable or dusty places. The width of the gasket should be at least the same as the width of the motor foot support surface; the gasket should have appropriate holes to allow opening of the foot bolts; there should be no burrs around any of the gaskets.

 

After this series slip ring type rotor motor is in place, 8 adjustment nuts should be welded on the steel gasket plate around the motor, adjusting the motor in all directions with adjustment bolts. Then, use the top wire on the motor foot to adjust the height. To be found after the motor, a comprehensive check of the motor and the base or the base between the installation gap, with a tape measure and note down the size of the gap at each location, the location and the depth of insertion of the tape measure (generally less than 0.05mm gap is not taken into account), according to the measured size of the production of a variety of good gasket required, the length of which should be inserted into the depth of the tape measure than the length out of 15mm or so, to do a good job in the gasket in the corresponding position of the insertion of the tightly, the long part towards the top against the motor base. When multiple layers of thin gaskets stacked to a certain thickness should be replaced by a single layer of the same thickness of the gasket.

 

Motor in the complete set of equipment on the base or foundation pad in place, such as the motor for rolling bearings can use the coupling to find the right. If the motor with slip ring type rotor uses sliding bearing, when coiling, the motor must be taken into account with axial clearance to prevent axial thrust damage to the motor.

 

The motor and the dragged machinery to find the right through the use of a ruler in the coupling against the back of the wheel up and down the left and right four points of the test adjustment to achieve. Coupling up and down the right and left clearance readings should be the same (or error does not exceed 0.04 ~ 0.05mm), and then the motor shaft and the dragged machinery shaft together with the rotation, 90 degrees for an interval, a total of four times a week for measurement and notation. The concentricity of the motor and the trailed machinery can be corrected by placing two micrometers on one side of the coupling. Respectively touch the two half of the coupling backrest wheel side, and adjust the zero position of the two micrometers, micrometers once fixed, do not move, the motor shaft and the shaft of the dragged machinery together with a 360-degree rotation, the two micrometer pointers should be the same and repeat the original readings. Otherwise re-check the micrometer placement is firm, such as confirming the firmness of the two axes is not centered, must be re-adjusted, when the two micrometer counts within 0.04 ~ 0.05mm is considered to be satisfactory.

 

Main Technical Parameters

 

Frame	H1000mm
Power Scope	2500kW~5600kW
Voltage	10kV
Frequency	50Hz, 60Hz
Number of Poles	10P
Synchronous Speed	600rpm
Cooling Mechod	IC611
Protection Grade	IP55
Insulation Class	F(155℃)
Duty	S1
Mounting Type	IM B3

 

Outline Dimensions

 

 

 

Motor Parameters

 

Applications 

As one of the important pillars of the world economy, the development of the oil and gas industry is of great significance to national energy security and economic development. In the process of oil and gas extraction, high-voltage motor is one of the very key equipment.

 

High-voltage slip ring type rotor motors in the oil and gas industry mainly play two roles, on the one hand, it is used to drive the equipment for oil and gas mining operations, on the other hand, it is used to transport oil and gas pipeline transportation system. Since the process of oil and gas extraction requires a lot of high-intensity work, high-voltage motors need to have sufficient output power and reliable performance. At the same time, in the pipeline transportation system for oil and gas, high voltage motors also need to have high durability and stability to ensure the effective operation of the pipeline transportation system.

 

To meet these requirements, the high-voltage motors used in the oil and gas industry utilize advanced technologies and materials, with high-quality insulation materials and structural designs to ensure the reliability and high efficiency of the motors. At the same time, the high-voltage motor with slip ring type rotor also adopt professional lubrication technology and closed structure design, which can effectively reduce the maintenance and upkeep cost of the equipment and extend the service life of the equipment.